Wasp-barcode WLS8600 Product Reference Guide Manual do Utilizador Página 106
- Página / 144
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
WLS8600
4.3.1 Header/Terminator Selection
The header/terminator selection is not effected by the reading of the restore default
code. In fact, header and terminator default values depend on the interface selection:
RS-232: no header, terminator CR-LF
WEDGE: no header, terminator ENTER
These default values are always restored through the reading of RS-232 or WEDGE
interface selection code, see chapter 2.
For the WEDGE interface, the following extended keyboard values can also be
configured:
EXTENDED KEYBOARD TO HEX CONVERSION TABLE
IBM AT
IBM 3153
APPLE ADB
IBM XT IBM 31xx, 32xx,
34xx, 37xx
Wyse
Digital
HEX KEY KEY KEY KEY
83
ENTER
ENTER
FIELD EXIT
RETURN
84
TAB
TAB
TAB
TAB
85
F1
F1
F1
F1
86
F2
F2
F2
F2
87
F3
F3
F3
F3
88
F4
F4
F4
F4
89
F5
F5
F5
F5
8A
F6
F6
F6
F6
8B
F7
F7
F7
F7
8C
F8
F8
F8
F8
8D
F9
F9
F9
F9
8E
F10
F10
F10
F10
8F
F11
ESC
F11
F11
90
F12
BACKSPACE
F12
F12
91
HOME
HOME
ENTER
F13
92
END
END
RESET
F14
93
PG UP
PG UP
INSERT
F15
94
PG DOWN
PG DOWN
DELETE
F16
95
↑
↑
FIELD -
UP
96
↓
↓
FIELD +
DOWN
97
←
←
ENTER (Paddle)
LEFT
98
→
→
PRINT
RIGHT
99
ESC
ESC
ESC
9A
CTRL (Right)
CTRL (Right)
CTRL (Right)
9B
Euro
Space
Space
Space
For all devices using IBM AT (compatible) Wedge or USB-KBD interfaces, all values from 9C to
FE send the relative simulated keypress when available or else the relative ALT-Mode
sequence. See the Hex to Character Conversion Table in Appendix
C.
For all devices using other Wedge interfaces, all values from 9C to FE send the Space
character.
100
- Reference Manual 1
- CONTENTS 3
- GENERAL VIEW 6
- 1 INTRODUCTION 7
- 2 INSTALLATION 8
- INSTALLATION 9
- CAUTION 9
- 2.2 RS-232 CONNECTION 10
- 2.3 USB 10
- 2.4 IBM USB POS 10
- 2.5 WEDGE CONNECTION 11
- 3 CONFIGURATION 12
- 3.2 SETUP PROCEDURES 13
- Ì$+CP0$-$Î 15
- Ì$+CM2EC0$->Î 15
- Ì$+CM1$-ÈÎ 15
- Ì$+CM0$-ÃÎ 15
- Ì$+CP6$-BÎ 15
- First Start-Up 18
- RS-232 PARAMETERS 21
- BAUD RATE 22
- DATA BITS 23
- STOP BITS 23
- HANDSHAKING 23
- ACK/NACK PROTOCOL 24
- INTER-CHARACTER DELAY 24
- RX TIMEOUT 25
- SERIAL TRIGGER LOCK 25
- USB PARAMETERS 26
- USB-COM 27
- USB-KBD 29
- KEYBOARD NATIONALITY 29
- INTER-CODE DELAY 31
- USB KEYBOARD SPEED 31
- WEDGE PARAMETERS 32
- CAPS LOCK 34
- NUM LOCK 35
- KEYBOARD SETTING 36
- CONTROL CHARACTER EMULATION 38
- PEN EMULATION 39
- OPERATING MODE 40
- MINIMUM OUTPUT PULSE 41
- CONVERSION TO CODE 39 42
- OVERFLOW 42
- OUTPUT LEVEL 43
- IDLE LEVEL 43
- INTER-BLOCK DELAY 43
- DATA FORMAT 44
- CODE IDENTIFIER 46
- CUSTOM CODE IDENTIFIER 46
- four character header 47
- TERMINATOR 48
- SPECIAL KEYS 48
- FIELD ADJUSTMENT 50
- FIELD ADJUSTMENT CHARACTER 51
- CODE LENGTH TX 51
- CHARACTER REPLACEMENT 52
- POWER SAVE 54
- SLEEP STATE 55
- ENTER SLEEP TIMEOUT 55
- READING PARAMETERS 56
- TRIGGER TYPE 57
- TRIGGER SIGNAL 57
- TRIGGER CLICK 57
- TRIGGER-OFF TIMEOUT 58
- FLASH MODE 58
- READS PER CYCLE 58
- SAFETY TIME 59
- BEEPER INTENSITY 59
- BEEPER TONE 60
- BEEPER TYPE 60
- BEEPER LENGTH 60
- GOOD READ SPOT DURATION 61
- AIMING SYSTEM 61
- DECODING PARAMETERS 62
- INK SPREAD 63
- OVERFLOW CONTROL 63
- INTERDIGIT CONTROL 63
- DECODING SAFETY 64
- PUZZLE SOLVER™ 64
- CODE SELECTION 65
- Ì#+AUTOWÎ 66
- EAN/UPC FAMILY 68
- ÌAA8Ad03Î 69
- ÌAA8Ad19Î 69
- 2/5 FAMILY 74
- CODE 39 FAMILY 75
- CODE 128 FAMILY 76
- CODE 93 77
- CODABAR FAMILY 77
- CODE 11 80
- CODE 16K 81
- CODE 49 81
- GS1 DATABAR™ CODES 82
- CONCATENATION 84
- ADVANCED FORMATTING 100
- 4 REFERENCES 102
- 4.1.2 ACK/NACK Protocol 103
- 4.1.3 FIFO 103
- 4.2 PEN PARAMETERS 104
- 4.2.1 Minimum Output Pulse 104
- 4.2.3 Overflow 104
- 4.1.4 RX Timeout 104
- 4.2.5 Inter-Block Delay 105
- 4.3 DATA FORMAT 105
- Enter Configuration 107
- Exit and Save Configuration 107
- REFERENCES 109
- WLS8600 110
- ÌFQ9C2>Î 112
- 4.4 POWER SAVE 115
- 4.4.1 Sleep State 115
- 4.4.2 Enter Sleep Timeout 115
- 4.5 READING PARAMETERS 116
- 4.5.1 Trigger Signal 116
- 4.5.2 Trigger Click 116
- 4.5.3 Trigger-Off Timeout 116
- 4.5.4 Reads per Cycle 116
- 4.5.5 Safety Time 117
- 4.6 DECODING PARAMETERS 117
- 4.6.1 Ink-Spread 117
- 4.6.2 Overflow Control 117
- 4.6.3 Interdigit Control 118
- 4.7 ADVANCED FORMATTING 118
- 4.7.1 Match Conditions 118
- Ì$+$*oÎ 119
- Ì$+$!KÎ 119
- Ì$+$&_Î 119
- Ì$+$0ÂÎ 120
- Ì$+$1$Î 120
- Ì#+CODEÂÎ 120
- Ì$+ZZ0$-*Î 121
- 5 TECHNICAL FEATURES 123
- 5.2 STATUS INDICATORS 124
- 5.3 READING TABLE 125
- SERIAL CONFIGURATION STRINGS 126
- (not for USB-KBD-ALT-MODE) 128
- (IBM AT compatible only) 128
- B CODE IDENTIFIER TABLE 137
- C HEX AND NUMERIC TABLE 140
- Wasp Barcode Technologies 144
- 1400 10th Street 144
- Plano, Texas USA 75074 144
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais