Wasp-barcode WLS8600 Product Reference Guide Manual do Utilizador Página 134
- Página / 144
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
WLS8600
CODE SELECTION (continued)
DESCRIPTION
STRING
UPC A check digit transmission
disable
AAI0
enable
AAI1
UPC E check digit transmission
disable
AAJ0
enable
AAJ1
conversions
UPC E to UPC A
AAA
UPC E to EAN 13
AAB
UPC A to EAN 13
AAC
EAN 8 to EAN 13
AAD
ISBN Conversion codes
enable ISBN
AP1
enable ISSN
AP2
enable ISBN and ISSN
AP3
disable ISBN and ISSN
AP0
Code 39
disable Code 39 family
AB0
Standard
no check digit control
AB11
check digit control and transmission
AB12
check digit control without transmission
AB13
Full ASCII
no check digit control
AB21
check digit control and transmission
AB22
check digit control without transmission
AB23
CIP 39
AB3
Code 32
AB4
code length
AB*xxxx
2/5
disable Code 2/5 family
AC0
Interleaved 2/5
no check digit control
AC11xxxx
check digit control and transmission
AC12xxxx
check digit control without transmission
AC13xxxx
Normal 2/5 5 bars
no check digit control
AC21xxxx
check digit control and transmission
AC22xxxx
check digit control without transmission
AC23xxxx
Industrial 2/5 (IATA)
no check digit control
AC31xxxx
check digit control and transmission
AC32xxxx
check digit control without transmission
AC33xxxx
Matrix 2/5 3 bars
no check digit control
AC41xxxx
check digit control and transmission
AC42xxxx
check digit control without transmission
AC43xxxx
CIP/HR
AC5
xxxx = ASCII numbers that define the code length where:
• First 2 digits = minimum acceptable code length.
• Second 2 digits = maximum acceptable code length.
The minimum code length must always be less than or equal to the maximum.
The maximum code length for all codes is 99 characters:
Examples:
0132 = variable length from 1 to 32 digits in the code.
1010 = 10 digit code length only.
128
- Reference Manual 1
- CONTENTS 3
- GENERAL VIEW 6
- 1 INTRODUCTION 7
- 2 INSTALLATION 8
- INSTALLATION 9
- CAUTION 9
- 2.2 RS-232 CONNECTION 10
- 2.3 USB 10
- 2.4 IBM USB POS 10
- 2.5 WEDGE CONNECTION 11
- 3 CONFIGURATION 12
- 3.2 SETUP PROCEDURES 13
- Ì$+CP0$-$Î 15
- Ì$+CM2EC0$->Î 15
- Ì$+CM1$-ÈÎ 15
- Ì$+CM0$-ÃÎ 15
- Ì$+CP6$-BÎ 15
- First Start-Up 18
- RS-232 PARAMETERS 21
- BAUD RATE 22
- DATA BITS 23
- STOP BITS 23
- HANDSHAKING 23
- ACK/NACK PROTOCOL 24
- INTER-CHARACTER DELAY 24
- RX TIMEOUT 25
- SERIAL TRIGGER LOCK 25
- USB PARAMETERS 26
- USB-COM 27
- USB-KBD 29
- KEYBOARD NATIONALITY 29
- INTER-CODE DELAY 31
- USB KEYBOARD SPEED 31
- WEDGE PARAMETERS 32
- CAPS LOCK 34
- NUM LOCK 35
- KEYBOARD SETTING 36
- CONTROL CHARACTER EMULATION 38
- PEN EMULATION 39
- OPERATING MODE 40
- MINIMUM OUTPUT PULSE 41
- CONVERSION TO CODE 39 42
- OVERFLOW 42
- OUTPUT LEVEL 43
- IDLE LEVEL 43
- INTER-BLOCK DELAY 43
- DATA FORMAT 44
- CODE IDENTIFIER 46
- CUSTOM CODE IDENTIFIER 46
- four character header 47
- TERMINATOR 48
- SPECIAL KEYS 48
- FIELD ADJUSTMENT 50
- FIELD ADJUSTMENT CHARACTER 51
- CODE LENGTH TX 51
- CHARACTER REPLACEMENT 52
- POWER SAVE 54
- SLEEP STATE 55
- ENTER SLEEP TIMEOUT 55
- READING PARAMETERS 56
- TRIGGER TYPE 57
- TRIGGER SIGNAL 57
- TRIGGER CLICK 57
- TRIGGER-OFF TIMEOUT 58
- FLASH MODE 58
- READS PER CYCLE 58
- SAFETY TIME 59
- BEEPER INTENSITY 59
- BEEPER TONE 60
- BEEPER TYPE 60
- BEEPER LENGTH 60
- GOOD READ SPOT DURATION 61
- AIMING SYSTEM 61
- DECODING PARAMETERS 62
- INK SPREAD 63
- OVERFLOW CONTROL 63
- INTERDIGIT CONTROL 63
- DECODING SAFETY 64
- PUZZLE SOLVER™ 64
- CODE SELECTION 65
- Ì#+AUTOWÎ 66
- EAN/UPC FAMILY 68
- ÌAA8Ad03Î 69
- ÌAA8Ad19Î 69
- 2/5 FAMILY 74
- CODE 39 FAMILY 75
- CODE 128 FAMILY 76
- CODE 93 77
- CODABAR FAMILY 77
- CODE 11 80
- CODE 16K 81
- CODE 49 81
- GS1 DATABAR™ CODES 82
- CONCATENATION 84
- ADVANCED FORMATTING 100
- 4 REFERENCES 102
- 4.1.2 ACK/NACK Protocol 103
- 4.1.3 FIFO 103
- 4.2 PEN PARAMETERS 104
- 4.2.1 Minimum Output Pulse 104
- 4.2.3 Overflow 104
- 4.1.4 RX Timeout 104
- 4.2.5 Inter-Block Delay 105
- 4.3 DATA FORMAT 105
- Enter Configuration 107
- Exit and Save Configuration 107
- REFERENCES 109
- WLS8600 110
- ÌFQ9C2>Î 112
- 4.4 POWER SAVE 115
- 4.4.1 Sleep State 115
- 4.4.2 Enter Sleep Timeout 115
- 4.5 READING PARAMETERS 116
- 4.5.1 Trigger Signal 116
- 4.5.2 Trigger Click 116
- 4.5.3 Trigger-Off Timeout 116
- 4.5.4 Reads per Cycle 116
- 4.5.5 Safety Time 117
- 4.6 DECODING PARAMETERS 117
- 4.6.1 Ink-Spread 117
- 4.6.2 Overflow Control 117
- 4.6.3 Interdigit Control 118
- 4.7 ADVANCED FORMATTING 118
- 4.7.1 Match Conditions 118
- Ì$+$*oÎ 119
- Ì$+$!KÎ 119
- Ì$+$&_Î 119
- Ì$+$0ÂÎ 120
- Ì$+$1$Î 120
- Ì#+CODEÂÎ 120
- Ì$+ZZ0$-*Î 121
- 5 TECHNICAL FEATURES 123
- 5.2 STATUS INDICATORS 124
- 5.3 READING TABLE 125
- SERIAL CONFIGURATION STRINGS 126
- (not for USB-KBD-ALT-MODE) 128
- (IBM AT compatible only) 128
- B CODE IDENTIFIER TABLE 137
- C HEX AND NUMERIC TABLE 140
- Wasp Barcode Technologies 144
- 1400 10th Street 144
- Plano, Texas USA 75074 144
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais